The following attributes are only used if a gusset part has been specified.
Name |
User Name |
Category |
On Property Page |
Read Only |
---|---|---|---|---|
GussetQuantity |
Gusset Quantity |
Standard |
No |
Yes |
GussetAngle |
Gusset Angle |
Dimensions |
Yes |
No |
Attributes |
Description |
Implementation Details |
---|---|---|
IJUAhsGussetQuant:: GussetQuantity |
Specifies the number of Gusset plates required. |
|
IJOAhsGussetAngle::GussetAngle |
Specifies the rotation of the Gusset part. This is the rotation of all the gussets about the dummy pipe. The angle between gussets depends on the ‘GussetQuantity’. Angle between two Gussets=360/GussetQuantity For Example, if GussetQuantity=2 then Angle between gussets=360/2=180 if GussetQuantity=4 then Angle between gussets=360/4=90 |
For Example, If GussetAngle = 0, If GussetAngle = 45, |
Welds
The Dummy Leg support defines welds using multiple attributes on the support instead of using auxiliary sheets. The following weld attributes specify the welds that must be included in the Dummy Leg support:
Attribute Name |
Description |
Implementation Details |
---|---|---|
IJUAhsRepadWeld:: RepadWeldPart |
The Weld Part-Number or Part Class to use for the support. If you intend to select the Part-Number using the RepadWeldRule, then this attribute should be left blank. |
Option 1 – Specify a Part-Number or Part Class directly WeldPart "S3Dhs_WeldPoint-2" WeldRule " " Option 2 – Use a HgrRule to get the Part WeldPart " " WeldRule "WeldByPipeSize" The repad weld will only be included if there is a repad in the support. The cap weld will only be included if there is a cap plate in the support. |
IJUAhsRepadWeldRl:: RepadWeldRule |
An HgrSupportRule that returns a Weld Part-Number. The Hanger Rule should be present in the catalog; it can be the name of a rule, or a rule ProgID. If you intend to specify a Part-Number directly using RepadWeldPart, then this attribute should be left blank. |
|
IJUAhsDummyWeld1:: DummyWeld1Part |
The Weld Part-Number or Part Class to use for the support. If you intend to select the Part-Number using the DummyWeld1Rule, then this attribute should be left blank. |
|
IJUAhsDummyWeld1Rl:: DummyWeld1Rule |
An HgrSupportRule that returns a Weld Part-Number. The Hanger Rule should be present in the catalog; it can be the name of a rule, or a rule ProgID. If you intend to specify a Part-Number directly using DummyWeld1Part, then this attribute should be left blank. |
|
IJUAhsDummyWeld2:: DummyWeld2Part |
The Weld Part-Number or Part Class to use for the support. If you intend to select the Part-Number using the DummyWeld2Rule, then this attribute should be left blank. |
|
IJUAhsDummyWeld2Rl:: DummyWeld2Rule |
An HgrSupportRule that returns a Weld Part-Number. The Hanger Rule should be present in the catalog; it can be the name of a rule, or a rule ProgID. If you intend to specify a Part-Number directly using DummyWeld2Part, then this attribute should be left blank. |
|
IJUAhsBPlateWeld:: BasePlateWeldPart |
The Weld Part-Number or Part Class to use for the support. If you intend to select the Part-Number using the BasePlateWeldPartRule, then this attribute should be left blank. |
|
IJUAhsBPlateWeldRl:: BasePlateWeldRule |
An HgrSupportRule that returns a Weld Part-Number. The Hanger Rule should be present in the catalog; it can be the name of a rule, or a rule ProgID. If you intend to specify a Part-Number directly using BasePlateWeldPart, then this attribute should be left blank. |
Repad Weld Location
Dummy with Repad
Dummy Weld 1 Location
Dummy with Repad
Dummy without Repad
Dummy Weld 2
Weld located at the bottom of the Dummy section
Base Plate Weld
Weld located at the bottom of the Base Plate
-
Dummy SmartPart that includes Base Plate graphic without Base Plate part
-
Dummy SmartPart that does not include Base Plate graphic with Base Plate part
-
Steel section with Base Plate part
Weld located at the bottom of the Base Plate
-
Dummy SmartPart that includes Base Plate graphic with Base Plate part