A Pipe to Pipe support uses the following configuration:
Name |
User Name |
Category |
On Property Page |
Read Only |
---|---|---|---|---|
Overhang1 |
Overhang 1 |
Dimensions |
Yes |
No |
Overhang1Rule |
Overhang 1 - Rule |
Dimensions |
No |
Yes |
Overhang1Definition |
Overhang 1 - Definition |
Dimensions |
No |
Yes |
Overhang1Selection |
Overhang 1 - Selection |
Dimensions |
No |
Yes |
Overhang2 |
Overhang 2 |
Dimensions |
Yes |
No |
Overhang2Rule |
Overhang 2 - Rule |
Dimensions |
No |
Yes |
Overhang2Definition |
Overhang 2 - Definition |
Dimensions |
No |
Yes |
Overhang2Selection |
Overhang 2 - Selection |
Dimensions |
No |
Yes |
PipeAttQty1 |
Pipe Attachment Quantity 1 |
Dimensions |
Yes |
No |
PipeAttQty1Rule |
Pipe Attachment Quantity 1 - Rule |
Dimensions |
No |
Yes |
PipeAttQty1Definition |
Pipe Attachment Quantity 1 - Definition |
Dimensions |
No |
Yes |
PipeAttQty1Selection |
Pipe Attachment Quantity 2 - Selection |
Dimensions |
No |
Yes |
PipeAttQty2 |
Pipe Attachment Quantity 2 |
Dimensions |
Yes |
No |
PipeAttQty2Rule |
Pipe Attachment Quantity 2 - Rule |
Dimensions |
No |
Yes |
PipeAttQty2Definition |
Pipe Attachment Quantity 2 - Definition |
Dimensions |
No |
Yes |
PipeAttQty2Selection |
Pipe Attachment Quantity 2 - Selection |
Dimensions |
No |
Yes |
PipeAttOffset1 |
Pipe Attachment Offset 1 |
Dimensions |
Yes |
No |
PipeAttOff1Rule |
Pipe Attachment Offset 1 - Rule |
Dimensions |
No |
Yes |
PipeAttOff1Definition |
Pipe Attachment Offset 1 - Definition |
Dimensions |
No |
Yes |
PipeAttOff1Selection |
Pipe Attachment Offset1 - Selection |
Dimensions |
No |
Yes |
PipeAttOffset2 |
Pipe Attachment Offset 2 |
Dimensions |
Yes |
No |
PipeAttOff2Rule |
Pipe Attachment Offset 2 - Rule |
Dimensions |
No |
Yes |
PipeAttOff2Definition |
Pipe Attachment Offset 2 - Definition |
Dimensions |
No |
Yes |
PipeAttOff2Selection |
Pipe Attachment Offset 2 - Selection |
Dimensions |
No |
Yes |
ShoeHeight |
Shoe Height - Value |
Dimensions |
Yes |
No |
ShoeHeightRule |
Shoe Height - Rule |
Dimensions |
Yes |
No |
ShoeHeightDefinition |
Shoe Height - Definition |
Dimensions |
Yes |
No |
SheHeightSelection |
Shel Height - Selection |
Dimensions |
Yes |
No |
Attribute Name |
Description |
Implementation Details |
---|---|---|
IJUAhs_PipeToPipeOH1:: |
Specifies the Overhang 1 value for the support. |
The following definitions are supported: 1 - Outside Edge of Pipe 2 - Center of Pipe 3 - Inside Edge of Pipe 4 - Middle of UBolt |
IJUAhs_PipeToPipeOH2:: |
Specifies the Overhang 2 value for the support. |
The following definitions are supported: 1 - Outside Edge of Pipe 2 - Center of Pipe 3 - Inside Edge of Pipe 4 - Middle of UBolt |
IJUAhs_PipeAttQty1:: IJUAhs_PipeAttQty2:: |
Specifies the number of pipe attachments the software places on each pipe. |
|
IJUAhs_PipeAttOff1:: IJUAhs_PipeAttOff2:: |
Specifies the offset value for the pipe attachment, if the pipe attachment exists. |
1 - Measured from Center If there are two pipe attachments, the software offsets the attachments in opposite directions. |
IJUAhs_ShoeHeight:: |
Specifies the shoe height. The software measures shoe height for the first selected pipe. |
1 - Bottom of Pipe For orthogonal configuration, measure from the bottom of the lowest pipe. |
IJUAhs_InsulOffset:: |
Specifies the value for the insulation offset, if the insulation is available. |
The default units are specified in the CustomInterface worksheet of the HS_S3DAssy workbook; otherwise, specify the units. Example: 25, 25mm, 25in. |
IJUAhs_InsulOffsetRl:: |
Specifies a hgrSupportRule that returns an insulation offset value. The hanger rule must be the name of an existing rule in the catalog. To specify the offset using InsulOffset, do not type any value for this property. |
Examples: Rule Name: Offset2ByPipeSize Rule ProgID: HS_S3DRules.Offset2ByPipeSize |
IJUAhs_InsulOffsetDef:: InsulOffsetDef |
Specifies the position where the software measures the insulation. |
1 - Measured from center |
IJUAhs_InsulOffsetSel:: InsulOffsetSel |
Specifies the attribute that selects the insulation offset. The default InsulOffset attribute is used if you do not specify a value. |
hsSelection: 1 - By Rule 2 - By Input |
IJUAhs_InsulLength:: InsulLength |
Specifies the length of the insulation. |
The default units are specified in the CustomInterface worksheet of the HS_S3DAssy workbook; otherwise specify the units. For example, 25, 25mm, 3in. |
IJUAhs_InsulLengthRl:: InsulLengthRule |
Specifies a hgrSupportRule that returns the insulation length value. The hanger rule must be the name of an existing rule in the catalog. To specify the offset using InsulLength, do not type any value for this property. |
Examples: Rule Name: Gap2ByPipeSize Rule ProgID: HS_S3DRules.Gap2ByPipeSize |
IJUAhs_InsulLengthSel:: InsulLengthSelection |
Specifies the attribute that selects the insulation offset. The default InsulOffset attribute is used if you do not specify a value. |
hsSelection: 1 - By Rule 2 - By Input |