The following attributes define the Base Spring data driven assembly used to form the Base Spring support. For more information on how to use the attributes, see Part Specifications.
Name |
User Name |
Category |
On Property Page |
Read Only |
---|---|---|---|---|
PipeOffset |
Pipe Offset |
Dimensions |
Yes |
No |
PipeOffsetRule |
Pipe Offset Rule |
Dimensions |
No |
Yes |
PipeOffsetSelection |
Pipe Offset Selection |
Dimensions |
No |
Yes |
PipeOffsetDefinition |
Pipe Offset Definition |
Dimensions |
No |
Yes |
Offset1 |
Offset 1 |
Dimensions |
Yes |
No |
Offset1Rule |
Offset 1 Rule |
Dimensions |
No |
Yes |
Offset1Selection |
Offset 1 Selection |
Dimensions |
No |
Yes |
Offset1Definition |
Offset 1 Definition |
Dimensions |
No |
Yes |
Offset2 |
Offset 2 |
Dimensions |
Yes |
No |
Offset2Rule |
Offset 2 Rule |
Dimensions |
No |
Yes |
Offset2Selection |
Offset 2 Selection |
Dimensions |
No |
Yes |
Offset2Definition |
Offset 2 Definition |
Dimensions |
No |
Yes |
SpringAngle |
Spring Angle |
Dimensions |
Yes |
No |
SpringAngle2 |
Spring Angle 2 |
Dimensions |
Yes |
No |
PipeAttAngle |
Pipe Attachment Angle |
Standard |
Yes |
No |
TotalLoad |
Total Load |
Standard |
No |
Yes |
TotalTravel |
Total Travel |
Standard |
Yes |
No |
ActualTravel |
Actual Travel |
Standard |
Yes |
No |
TravelDir |
Travel Direction |
Standard |
No |
Yes |
VarHeightSupport |
Variable Height Support |
Standard |
Yes |
No |
DummyLength |
Dummy Length |
Dimensions |
Yes |
No |
StanchionLength |
Stanchion Length |
Dimensions |
Yes |
No |
DummyLengthStart |
Dummy Length Start |
Dimensions |
Yes |
Yes |
DummyOffset |
Dummy Offset |
Dimensions |
Yes |
No |
Attribute Name |
Description |
Implementation Details |
---|---|---|
IJUAhsPipeOffset:: |
Specifies the offset from the top of the base spring to the pipe. |
Use the following values: 1 - Centerline 2 - Bottom of Pipe |
IJUAhsOffset1:Offset1 IJUAhsOffset2:Offset2 |
Specifies the offset from the pipe to the respective spring. |
Use the following value: 1 - Centerline The software ignores Offset2 if the spring quantity is not equal to 2. |
IJUAhsSpringAngle:: IJUAhsSpringAngle2:: |
Specifies the angle of rotation for each constant spring. |
|
IJUAhsPipeAttAngle:: |
Specifies the angle at which to attach the pipe. This attribute is applicable for vertical pipe configuration only. |
|
IJUAHgrRH_VS_TotalLoad:: IJUAHgrRH_CS_TotalLoad:: |
Specifies the total load. |
|
IJUAHgrRH_VS_ IJUAHgrRH_CS_ |
Specifies the actual travel. |
|
IJUAHgrRH_VS_TravelDir:: IJUAHgrRH_CS_TravelDir:: |
Specifies the direction of the spring movement. |
hsSpringMovementDir: 1 - Up 2 - Down |
IJUAhsDummyVarHeight:: VarHeightSupport |
A codelist specifying which secondary support should have a variable height. |
Possible Values: 1 – DummyLeg 2 – Stanchion 3 – AdjustableBase |
IJUAhsDummyLength:: DummyLength |
Specifies the length of the dummy leg based on the DummyLengthStart attribute in the secondary support. |
If the Dummy Leg is the variable height support then this attribute can be left empty. |
IJUAhsStanchionLength::StanchionLength |
Specifies the length of the stanchion in the secondary support. |
If the Stanchion is the variable height support then this attribute can be left empty. |
IJUAhsDummyLenDim:: DummyLengthStart |
The starting position for the length measurement. |
Supported Values 1 = Pipe Centerline – Horizontal Pipe 2 = Bottom of Pipe – horizontal Pipe 3 = Top of Turn |
IJOAhsDummyOffset::Offset |
Specifies the dummy offset from its center line |