Input Dimensions
The following attributes specify the input dimension attributes of a Beam to Beam support:
Name |
User Name |
Category |
On Property Page |
Read only |
---|---|---|---|---|
BeamOffset |
Beam Offset |
Dimensions |
Yes |
No |
BeamOffsetRl |
Beam Offset - Rule |
Dimensions |
Yes |
No |
BeamOffsetSEl |
Beam Offset - Selection |
Dimensions |
Yes |
No |
BBGap |
Back To Back Gap |
Dimensions |
Yes |
No |
BBGapRl |
Back To Back Gap - Rule |
Dimensions |
Yes |
No |
BBGapSel |
Back To Back Gap - Selection |
Dimensions |
Yes |
No |
BeamEndOffset(1&2) |
Beam End Offset (1 & 2) |
Dimensions |
Yes |
No |
BeamEndOffsetRl(1&2) |
Beam End Offset (1 & 2) - |
Dimensions |
Yes |
No |
BeamEndOffsetSel |
Beam End Offset (1 & 2) - |
Dimensions |
Yes |
No |
ClipLength(1&2) |
Clip Length (1 & 2) |
Dimensions |
Yes |
No |
ClipLengthRl(1&2) |
Clip Length (1 & 2) - |
Dimensions |
Yes |
No |
ClipLengthSel(1&2) |
Clip Length (1 & 2) - |
Dimensions |
Yes |
No |
VertPltOH(1&2) |
Vertical Plate Overhang |
Dimensions |
Yes |
No |
VertPltOHRl(1&2) |
Vertical Plate Overhang |
Dimensions |
Yes |
No |
VertPltOHSel(1&2) |
Vertical Plate Overhang |
Dimensions |
Yes |
No |
Attribute Name |
Description |
Implementation Details |
---|---|---|
IJUAhsBeamOffset:: |
Specifies the offset of the Beam to Beam support from the primary supporting structure. The offset definition depends on the primary Beam connection value. |
Use the following values: 1 - Above 2 - Top 3 - Top Inside 4 - Center 5 - Bottom Inside 6 - Bottom 7 - Below 8 - Vertical Plate |
IJUAhsBBGap::BBGap |
Specifies the gap between the back-to-back beams. |
|
IJUAhsEndOffset1:: |
Specifies the offset from the end of beam. BeamEndOffset1 applies to the beam end that is connected to the primary supporting structure. The offset definition depends on the primary beam connection value. |
1 - Above 2 - Top 3 - Top Inside 4 - Center 5 - Bottom Inside 6 - Bottom 7 - Below 8 - Vertical Plate |
IJUAhsEndOffset2:: |
Specifies the offset from the end of the beam. BeamEndOffset2 applies to the end of the beam that is connected to the secondary supporting structure. The offset definition depends on the secondary beam connection value. |
1 - Web 2 - Flange 3 - Vertical Plate |
IJUAhsClipLen1:: IJUAhsClipLen2:: |
Specifies the length of the Clip. ClipLength1 specifies the length of Clip 1 and ClipLength2 specifies the length of Clip 2. |
|
IJUAhsVertPltOH1:: IJUAhsVertPltOH2:: |
Specifies the overhang of the vertical Plate from the bottom of the Beam. VertPlateOverHang1 specifies the overhang of the vertical Plate 1. VertPlateOverhang2 specifies the overhang of vertical Plate 2. |
Output Dimensions
The following output dimension values are determined by Smart 3D and are displayed in the property page as read-only properties:
Name |
User Name |
Category |
On Property Page |
Read only |
---|---|---|---|---|
BeamSpan |
Beam Span |
Dimensions |
Yes |
Yes |
VerticalPlate1Length |
Vertical Plate 1 Length |
Dimensions |
Yes |
No |
VerticalPlate2Length |
Vertical Plate 2 Length |
Dimensions |
Yes |
No |
Attribute Name |
Description |
Implementation Details |
---|---|---|
IJUAhsBeamSpan:: |
Specifies the span of the Beam to Beam support. Span is the measurement between the centers of the Flanges of each supporting structure. |
|
IJUAhsVertPlt1Len:: IJUAhsVertPlt2Len:: |
Specifies the lengths of the vertical Plates, if included.
|
By Reference Inputs
The following attributes are used only when you use By Reference to place a support in the model:
-
IJUAhsStruct1Offset::Struct1Offset
-
IJUAhsStruct2Offset::Struct2Offset