Rich Hanger Beam Properties - Intergraph Smart 3D - Reference Data

Intergraph Smart 3D Hangers and Supports Vendor Parts

PPMProductFamily
3D Design and Visualization
PPMProduct
Intergraph Smart 3D
PPMCategory
Reference Data
Version_S3D
11.x(2016)

Rich Hanger Beam Properties

Basic Steel Properties

These attributes define the common properties of hanger beam steel.

IJOAHsHgrBeamType::HgrBeamType - Specifies whether the hanger beam is Cutback steel or Snipped steel. HgrBeamType is a codelisted value. Allowed values are from HS_System_Codelist.xls are 1- Cutback Steel and 2 - Snipped Steel.

  • Cutback steel is not supported for circular cross sections like HSSR and Pipe.

  • Snipped steel is supported only for L cross section.

IJUAhsOccOverLength:: BeginOverLength - Specifies the over length at the beginning of the steel. BeginOverLength can be either positive or negative.

IJUAhsOccOverLength:: EndOverLength - Specifies the over length at the end of the steel. EndOverLength can be either positive or negative.

IJUAhsOccLength::Length - Specifies the length of the steel. The software calculates Length using the start and end points in the graphic when you place the steel.

IJUAhsVarLength::VarLength - Specifies the cut length of the steel when you apply cutback angles, snip angles, or overlength on the steel.

Use the following properties to map and retrieve the geometry information from structural workbook, StructCrossSections-<Standard Name>.xls.

HgrRelation(i):ClassName - Specifies the cross section type. Example, L, C, W, and so on.

HgrRelation(i):Standard - Specifies the standard name. It is a codelisted value from HS_System_Codelist.xls. For example, AISC, CISC, Japan, China, Aust, and so on.

tHgrRelation(i):SectionName - Specifies the section name. Use the SecionName from StructCrossSections-<Standard Name>.xls. For example, HSS32x24x.625, C15x50, L8x8x1-1/8, and so on.

IJOAhsReflect::Reflect - Specifies the plane for the reflection of Rich Hanger Beam. The following codelist values are available in the hsReflectType sheet of the HS_S3DParts_Codelist workbook.

  • 0 - No

  • 1 - Along Flange Plane

  • 2 - Along Web Plane

IJOAhsReflect::ReflectPlaneOffset - Specifies the offset for the Reflect Plane from the Cardinal Point 1 of the section.

Cutback Steel Properties

These attributes define the cutback steel properties.

IJOAhsCutback::BeginCutbackAnchorPoint

Specifies the edge for the cutback at the begin face. The codelisted values from the CutbackAnchorPoint sheet in the HS_System_Codelist.xls are 2 - Bottom Center, 4 - Left Center, 6 - Right Center, and 8 - Top Center

IJOAhsCutback::EndCutbackAnchorPoint

Specifies the edge for the cutback at the end face. The codelisted values from the CutbackAnchorPoint sheet in the HS_System_Codelist.xls are 2 - Bottom Center, 4 - Left Center, 6 - Right Center, and 8 - Top Center

IJOAhsCutback:: CutbackBeginAngle

Specifies the start cutback angle for the steel. For CutbackAnchorPoint set to 2 or 8, the face ports rotate by the cutback angle and align along the cutback face.

IJOAhsCutback::CutbackEndAngle

Specifies the end cutback angle for the steel. For CutbackAnchorPoint set to 2 or 8, the face ports rotate by the cutback angle and align along the cutback face.

Angle Value

Attribute Populated

Anchor Point

Result

+ve

CutbackBeginAngle

2

Adds specified degrees

+ve

CutbackBeginAngle

4

Subtracts specified degrees

+ve

CutbackBeginAngle

6

Adds specified degrees

+ve

CutbackBeginAngle

8

Subtracts specified degrees

-ve

CutbackBeginAngle

2

Subtracts specified degrees

-ve

CutbackBeginAngle

4

Adds specified degrees

-ve

CutbackBeginAngle

6

Subtracts specified degrees

-ve

CutbackBeginAngle

8

Adds specified degrees

+ve

CutbackEndAngle

2

Subtracts specified degrees

+ve

CutbackEndAngle

4

Adds specified degrees

+ve

CutbackEndAngle

6

Subtracts specified degrees

+ve

CutbackEndAngle

8

Adds specified degrees

-ve

CutbackEndAngle

2

Adds specified degrees

-ve

CutbackEndAngle

4

Subtracts specified degrees

-ve

CutbackEndAngle

6

Subtracts specified degrees

-ve

CutbackEndAngle

8

Adds specified degrees

Snipped Steel Properties

These properties specify the Flange and Web modifications when a hanger is snipped by various offset values and angles.

IJOAhsSnipedSteel::CutbackBeginAngle1

Specifies the angle with which the begin face of the flange is snipped.

IJOAhsSnipedSteel::CutbackBeginAngle2

Specifies the angle with which the begin face of the web is snipped.

IJOAhsSnipedSteel::CutbackEndAngle1

Specifies the angle with which the end face of the flange is snipped.

IJOAhsSnipedSteel::CutbackEndAngle2

Specifies the angle with which the end face of the web is snipped.

IJOAhsSnipedSteel::BeginCutbackAnchorPoint1

Specifies the edge for the cutback at the begin face of the flange. The following codelisted values from the CutbackAnchorPoint sheet in the HS_System_Codelist.xls are valid:

  • 2 - Bottom Center

  • 8 - Top Center. BeginCutbackAnchorPoint1 (read-only value)

IJOAhsSnipedSteel::BeginCutbackAnchorPoint2

Specifies the edge for the cutback at the begin face of the web. The following codelisted values from the hsCutbackAnchorPoint sheet in HS_System_Codelist.xls are valid:

  • 4 - Left Center

  • 6 - Right Center. BeginCutbackAnchorPoint2 (read-only value)

IJOAhsSnipedSteel::EndCutbackAnchorPoint1

Specifies the plane for the cutback at the end face of the flange. The following codelisted values from the hsCutbackAnchorPoint sheet in HS_System_Codelist.xls are valid:

  • 2 - Bottom Center

  • 8 - Top Center. EndCutbackAnchorPoint1 (read-only value)

IJOAhsSnipedSteel::EndCutbackAnchorPoint2

Specifies the edge for the cutback at the end face of the web. The following codelisted values from the hsCutbackAnchorPoint sheet in HS_System_Codelist.xls are valid:

  • 4 - Left Center

  • 6 - Right Center. EndCutbackAnchorPoint2 (read-only value)

IJOAhsCutbackOffset::BeginOffsetAlongFlange

Specifies the offset with which the begin face of the flange is snipped.

IJOAhsCutbackOffset::BeginOffsetAlongWeb

Specifies the offset with which the begin face of the web is snipped.

IJOAhsCutbackOffset::EndOffsetAlongFlange

Specifies the offset with which the end face of the flange is snipped.

IJOAhsCutbackOffset::EndOffsetAlongWeb

Specifies the offset with which the end face of the web is snipped.

IJOAhsFacePortOrient::FacePortOrient

Specifies whether the face port orientation is aligned along the flange, or the web when a snip angle is applied. It is a codelisted value from the hsFacePortOrient sheet in the HS_System_Codelist.xls workbook. Allowed values are: 1 - Face Port Orient Along Flange and 2 - Face Port Orient Along Web.

Port Properties

IJOAhsSteelCP::CP1

Specifies the cardinal point of the BeginCap port. The default location of CP1 is 1.

IJOAhsSteelCP::CP2

Specifies the cardinal point of the EndCap port. The default location of CP2 is 1.

IJOAhsSteelCP::CP3

Specifies the cardinal point of the BeginFace port. The default location of CP3 is 5.

IJOAhsSteelCP::CP4

Specifies the cardinal point of the EndFace port. The default location of CP4 is 5.

IJOAhsSteelCP::CP5

Specifies the cardinal point of the Neutral port. The default location of CP5 is 5.

IJOAhsSteelCP::CP6

Specifies the cardinal point of the BeginFlex port. The default location of CP6 is 8.

IJOAhsSteelCP::CP7

Specifies the cardinal point of the EndFlex port. The default location of CP7 is 8.

IJOAhsBeginCap::BeginCapXOffset

Specifies the offset with which the BeginCap port is moved in the x-axis.

IJOAhsBeginCap::BeginCapYOffset

Specifies the offset with which the BeginCap port is moved in the y-axis.

IJOAhsBeginCap::BeginCapRotZ

Specifies the angle with which the BeginCap port is rotated about its z-axis.

IJOAhsEndCap::EndCapXOffset

Specifies the offset with which the EndCap port is moved in the x-axis.

IJOAhsEndCap::EndCapYOffset

Specifies the offset with which the EndCap port is moved in the y-axis.

IJOAhsEndCap::EndCapRotZ

Specifies the angle with which the EndCap port is rotated about its z-axis.

IJOAhsFlexPort::FlexPortXOffset

Specifies the offset with which the BeginFlex port is moved in the x-axis.

IJOAhsFlexPort::FlexPortYOffset

Specifies the offset with which the BeginFlex port is moved in the y-axis.

IJOAhsFlexPort::FlexPortZOffset

Specifies the offset with which the BeginFlex port is moved in the z-axis.

IJOAhsFlexPort::FlexPortRotX

Specifies the angle with which the BeginFlex port is rotated about its x-axis.

IJOAhsFlexPort::FlexPortRotY

Specifies the angle with which the BeginFlex port is rotated about its y-axis.

IJOAhsFlexPort::FlexPortRotZ

Specifies the angle with which the BeginFlex port is rotated about its z-axis.

IJOAhsEndFlexPort::EndFlexPortXOffset

Specifies the offset with which the EndFlex port is moved in the x-axis.

IJOAhsEndFlexPort::EndFlexPortYOffset

Specifies the offset with which the EndFlex port is moved in the y-axis.

IJOAhsEndFlexPort::EndFlexPortZOffset

Specifies the offset with which the EndFlex port is moved in the z-axis.

IJOAhsEndFlexPort::EndFlexPortRotX

Specifies the angle with which the EndFlex port is rotated about its x-axis.

IJOAhsEndFlexPort::EndFlexPortRotY

Specifies the angle with which the EndFlex port is rotated about its y-axis.

IJOAhsEndFlexPort::EndFlexPortRotZ

Specifies the angle with which the EndFlex port is rotated about its z-axis.