Structure Translation Maps - Intergraph Smart 3D - 2014 R1 - Administration

Intergraph Smart 3D PDMS Design and Data Exchange

PPMProductFamily
3D Design and Visualization
PPMProduct
Intergraph Smart 3D
PPMCategory
Administration
Version_S3D
10.1(2014R1)

Use the structure translation mapping sheets in the S3DPDMSExportMapping.xls workbook to map Smart 3D structure properties to the correct PDMS structure attributes. Before exporting Smart 3D structure model data to PDMS, you must modify these sheets to ensure that the following criteria have been met:

  • All of the cross-sections and respective cardinal points in the Smart 3D model are mapped to the corresponding cross-sections and PLine attributes in the PDMS catalog. This is mandatory for the export of members from Smart 3D. For more information, see Map cross-section and orientation mismatches.

  • All of the Marine cross-sections and respective load points in the Smart 3D model are mapped to the corresponding cross-sections and PLine attributes in the PDMS catalog. This is mandatory for the export of profile parts from Smart 3D.

  • In the PDMSExportTranslator.ini file, TransferInsulationAsGTypes is set so that insulation is exported using the mapping file, then the catalog must be set up for insulation on members. Also, all insulation encasements in the model must be created in the PDMS catalog and mapped to the corresponding fitting in PDMS.

After all of the mapping is completed in the S3DPDMSExportMapping.xls workbook, run the PDMS Export Validation command to validate the mapping data in the workbook. Any missing entries reported by the validation tool should be resolved. For more information, see PDMS Export Validation.

The following structure translation maps are delivered in the S3DPDMSExportMapping.xls workbook:

StructureClassMap

Maps the supported structure classes between Smart 3D and PDMS. This is the main mapping sheet for the structure discipline. For more information, see StructureClassMap .

CoordinateSystemMap

Maps coordinate system attributes between Smart 3D and PDMS. For more information, see CoordinateSystemMap.

ElevationPlaneMap

Maps elevation plane attributes between Smart 3D and PDMS. For more information, see ElevationPlaneMap.

GridLineMap

Maps grid line attributes between Smart 3D and PDMS. For more information, see GridLineMap.

LinearMemberPartAttrsMap

Maps linear member part attributes between Smart 3D and PDMS. This sheet is only applicable when using the software in Marine mode. For more information, see LinearMemberPartAttrsMap.

CurvedMemberPartAttrsMap

Maps curved member part attributes between Smart 3D and PDMS. This sheet is only applicable when using the software in Marine mode. For more information, see CurvedMemberPartAttrsMap.

InsulationAttrsMap

Maps insulation attributes between Smart 3D and PDMS. For more information, see InsulationAttrsMap.

SlabAttrsMap

Maps slab attributes between Smart 3D and PDMS. For more information, see SlabAttrsMap.

StairAttrsMap

Maps stair attributes between Smart 3D and PDMS. For more information, see StairAttrsMap.

LadderAttrsMap

Maps ladder attributes between Smart 3D and PDMS. For more information, see LadderAttrsMap.

HandRailAttrsMap

Maps handrail attributes between Smart 3D and PDMS. For more information, see HandRailAttrsMap.

FootingAttrsMap

Maps footing attributes between Smart 3D and PDMS. For more information, see FootingAttrsMap.

EquipmentFoundationAttrsMap

Maps equipment foundation attributes between Smart 3D and PDMS. For more information, see EquipmentFoundationAttrsMap.

LeafPlateSystemAttrsMap

Maps leaf plate system attributes between Smart 3D and PDMS. This sheet is only applicable when using the software in Marine mode. For more information, see LeafPlateSystemAttrsMap.

PlanarPlatePartAttrsMap

Maps planar plate system attributes between Smart 3D and PDMS. This sheet is only applicable when using the software in Marine mode. For more information, see PlanarPlatePartAttrsMap.

CurvedPlatePartAttrsMap

Maps curved plate part attributes between Smart 3D and PDMS. This sheet is only applicable when using the software in Marine mode. For more information, see CurvedPlatePartAttrsMap.

LeafStiffenerSystemAttrsMap

Maps leaf stiffener system attributes between Smart 3D and PDMS. This sheet is only applicable when using the software in Marine mode. For more information, see LeafStiffenerSystemAttrsMap.

LinearStiffenerPartAttrsMap

Maps linear stiffener part attributes between Smart 3D and PDMS. This sheet is only applicable when using the software in Marine mode. For more information, see LinearStiffenerPartAttrsMap.

CurvedStiffenerPartAttrsMap

Maps curved stiffener part attributes between Smart 3D and PDMS. This sheet is only applicable when using the software in Marine mode. For more information, see CurvedStiffenerPartAttrsMap.

LeafERSystemAttrsMap

Maps leaf edge reinforcement system attributes between Smart 3D and PDMS. This sheet is only applicable when using the software in Marine mode. For more information, see LeafERSystemAttrsMap.

LinearERProfilePartAttrsMap

Maps linear edge reinforcement profile part attributes between Smart 3D and PDMS. This sheet is only applicable when using the software in Marine mode. For more information, see LinearERProfilePartAttrsMap.

CurvedERProfilePartAttrsMap

Maps curved edge reinforcement profile part attributes between Smart 3D and PDMS. This sheet is only applicable when using the software in Marine mode. For more information, see CurvedERProfilePartAttrsMap.

LeafBeamSystemAttrsMap

Maps leaf beam system attributes between Smart 3D and PDMS. This sheet is only applicable when using the software in Marine mode. For more information, see LeafBeamSystemAttrsMap.

BeamPartAttrsMap

Maps beam part attributes between Smart 3D and PDMS. This sheet is only applicable when using the software in Marine mode. For more information, see BeamPartAttrsMap.

LinearSAStiffenerPartAttrsMap

Maps linear SA stiffener part attributes between Smart 3D and PDMS. This sheet is only applicable when using the software in Marine mode. For more information, see LinearSAStiffenerPartAttrsMap.

CurvedSAStiffenerPartAttrsMap

Maps curved SA stiffener part attributes between Smart 3D and PDMS. This sheet is only applicable when using the software in Marine mode. For more information, see CurvedSAStiffenerPartAttrsMap.

HoleFittingAttrsMap

Maps hole fitting object attributes between Smart 3D and PDMS. For more information, see HoleFittingAttrsMap.

WallSystemAttrsMap

Maps additional attributes for Smart 3D wall system. For more information, see .

StraightWallAttrsMap

Maps additional attributes for Smart 3D straight wall parts. For more information, see .

CurvedWallAttrsMap

Maps additional attributes for Smart 3D curved wall parts. For more information, see .

StructureGlobalsMap

Defines global settings for structural export. For more information, see StructureGlobalsMap.

InsulationAttrMap

Defines insulation encasement type design parameters for each cross-section type. For more information, see InsulationAttrMap.

InsulationSpecAttrMap

Defines insulation encasement type SpecRef attributes for each cross-section type. For more information, see InsulationSpecAttrMap.

StructClassAdditionalAttribute

Maps additional attributes for Smart 3D cross-sections. For more information, see StructClassAdditionalAttributes .

AISC-LRFD-HSSC, AISC-LRFD-PIPE, AISC-LRFD-L, AISC-LRFD-C, AISC-LRFD-WT, AISC-LRFD-HSSR, AISC-LRFD-W, AISC-LRFD-M, AISC-LRFD-S, AISC-LRFD-ST, AISC-LRFD-HP, AISC-LRFD-MC

Defines value mapping between a Smart 3D cross-section name and the PDMS cross-section SpecRef attribute for each specific cross-section type. For more information, see Cross-Section Maps.

TUBE_PLine, ANG_PLine, DINU_PLine, TEE_PLine, BOX_PLine, BEAM_PLine, SBM_PLine, STEE_PLine

Defines value mapping between Smart 3D cardinal points and the PDMS PLine attribute for each specific cross-section type. For more information, see Cardinal Point Maps.

MarineCSAdditionalAttributes

Maps additional attributes for Smart 3D cross-sections.

ShipShapes-I, ShipShapes-B, ShipShapes-FB, ShipShapes-ISType, ShipShapes-CSType, ShipShapes-H, ShipShapes-T_XType, ShipShapes-TSType, ShipShapes-EA, ShipShapes-RT, ShipShapes-P, ShipShapes-BUT, ShipShapes-C_SS, ShipShapes-UA, ShipShapes-BUTL2, ShipShapes-BUTL3, ShipShapes-HalfR, ShipShapes-R

Defines value mapping between a Smart 3D cross-section name and the PDMS cross-section SpecRef attribute for each specific cross-section type. This sheet is only applicable when using the software in Marine mode.

I_PLine, B_Pline, FB_Pline, ISType_Pline, CSType_Pline, H_Pline, T_XType_Pline, TSType_Pline, EA_Pline, RT_Pline, P_Pline, BUT_Pline, C_SS_Pline, UA_Pline, BUTL2_Pline, BUTL3_Pline, HalfR_Pline, R_Pline

Defines value mapping between Smart 3D load points and the PDMS PLine attribute for each specific cross-section type.

PDMSWallAdditionalAttributes

Defines mapping between PDMS SpecReference (SPRE), Material Reference (MATR), Grade (GRADE), and Cardinal Points (JUSL) attributes and relevant Smart 3D wall compositions. For more information, see PDMSWallAdditionalAttributes.

WallCrossSectionMap

Maps Smart 3D wall composition and PDMS SpecRef. For more information, seeWallCrossSectionMap .

WallCSAdditionalAttributesMap

Maps PDMS design parameters (wall thickness and wall height) to the relevant Smart 3D attributes. For more information, see WallCSAdditionalAttributesMap.

Wall_JUSL

Maps Smart 3D cardinal points to the relevant PDMS justification lines. For more information, see Wall_JUSL.

S3DMaterialAndGradeMap

Defines mapping between the Smart 3D Material-Grade value and the PDMS MatRef and Grade attribute. For more information, see S3DMaterialAndGradeMap.