Default Property Values Tab - Intergraph Smart 3D - Help

Intergraph Smart 3D Piping

PPMProduct
Intergraph Smart 3D
PPMCategory_custom
Help
SPFVersion_custom
2019 (10.0)
Version_S3D
11.x(2016)

Sets default property values for piping, electrical, and conduit systems.

Category

Select the category type in which you want to define default properties. Currently, you can select from the following categories: Responsibility, Standard, Surface Treatment and Coating, Testing, Insulation and Tracing, Cable Fill, and Temperature and Pressure.

Standard

Specification

Select the specification that you want to be the default for this system. You might need to use the Define Allowed Specifications command before you can select a specification here. You define specifications in the reference data.

Minimum Slope

Specifies the slope for the runs created in this system. You can specify the slope as a ratio, a percentage, or in degrees.

  • As a ratio, if a run drops 1/4" for every foot of horizontal distance, specify the slope as 1/4"/1'-0".

  • As a percentage, if a run drops 1" for every 10" of horizontal distance, specify the slope as 10%.

  • In degrees, a five-degree slope can be specified as 5deg.

Cable Fill

Fill Efficiency

Displays or defines the efficiency of the stacking of cables in the cableway. You can enter a real number, an integer, or a percent; for example, type 0.9, 90, or 90%.

Signal Type

Displays or defines the cable usage, which is used in tray fill calculations. If you want to add, edit, or remove values that are available for selection, edit the Signal Type select list in the Catalog task.

Voltage Grade

Displays or defines the voltage grade, which is used in determining the range of voltage that the cableway can carry. If you want to add, edit, or remove values that are available for selection, edit the Voltage Grade select list in the Catalog task.

Responsibility

Cleaning Responsibility

Select the party responsible for cleaning the object. If you want to add, edit, or remove values that are available for selection, edit the Cleaning Responsibility select list in the Catalog task.

Design Responsibility

Select the party responsible for designing the object. If you want to add, edit, or remove values that are available for selection, edit the Design Responsibility select list in the Catalog task.

Fabrication Responsibility

Select the party responsible for fabricating the object. If you want to add, edit, or remove values that are available for selection, edit the Fabrication Responsibility select list in the Catalog task.

Installation Responsibility

Select the party responsible for installing the object. If you want to add, edit, or remove values that are available for selection, edit the Installation Responsibility select list in the Catalog task.

Painting Responsibility

Select the party responsible for painting the object. If you want to add, edit, or remove values that are available for selection, edit the Painting Responsibility select list in the Catalog task.

Requisition Responsibility

Select the party responsible for ordering the object. If you want to add, edit, or remove values that are available for selection, edit the Requisition Responsibility select list in the Catalog task.

Supply Responsibility

Select the party responsible for delivering the object. If you want to add, edit, or remove values that are available for selection, edit the Supply Responsibility select list in the Catalog task.

Testing Responsibility

Select the party responsible for testing the weld on the object. If you want to add, edit, or remove values that are available for selection, edit the Testing Responsibility select list in the Catalog task.

Surface Treatment and Coating

Interior Surface Treatment Requirement

Select the interior treatment requirement for the object. If you want to add, edit, or remove values that are available for selection, edit the Interior Surface Treatment select list in the Catalog task.

Interior Surface Treatment Type

Select the interior treatment type for the object. If you want to add, edit, or remove values that are available for selection, edit the Interior Surface Treatment select list in the Catalog task.

Exterior Surface Treatment Requirement

Select the exterior treatment requirement for the object. If you want to add, edit, or remove values that are available for selection, edit the Exterior Surface Treatment select list in the Catalog task.

Exterior Surface Treatment Type

Select the exterior treatment type for the object. If you want to add, edit, or remove values that are available for selection, edit the Exterior Surface Treatment select list in the Catalog task.

Cleaning Requirement

Select the cleaning requirement for the object. If you want to add, edit, or remove values that are available for selection, edit the Cleaning Requirement select list in the Catalog task.

Steamout Requirement

Select the steam out requirement for the object. If you want to add, edit, or remove values that are available for selection, edit the Steamout Requirement select list in the Catalog task.

Steamout Pressure

Specify the steamout pressure for the object. Include the pressure unit of measure (psi for pounds per square inch, for example) when specifying this value.

Steamout Temperature

Specify the steamout temperature for the object. Include the temperature unit of measure (K for Kelvin, F for Fahrenheit, or C for Celsius, for example) when specifying this value.

Auxiliary Treatment Requirement

Specify any auxiliary treatment requirement.

Auxiliary Treatment Type

Specify any auxiliary treatment type.

Interior Coating Requirement

Select the interior coating requirement for the object. If you want to add, edit, or remove values that are available for selection, edit the Coating Type select list in the Catalog task.

Interior Coating Type

Select the interior coating type for the object. If you want to add, edit, or remove values that are available for selection, edit the Coating Type select list in the Catalog task.

Interior Coating Area

Enter total area that the coating covers.

Exterior Coating Requirement

Select the exterior coating requirement for the object. If you want to add, edit, or remove values that are available for selection, edit the Coating Type select list in the Catalog task.

Exterior Coating Type

Select the exterior coating type for the object. If you want to add, edit, or remove values that are available for selection, edit the Coating Type select list in the Catalog task.

Exterior Coating Area

Enter the total area that the coating covers.

Coating Color

Select the color of the object coating. If you want to add, edit, or remove values that are available for selection, edit the Coating Color select list in the Catalog task.

Testing

Testing Requirement

Specifies whether non-destructive testing of welds is required.

Testing Type

Select the type of non-destructive weld testing for the welds. If you want to add, edit, or remove values that are available for selection, edit the Testing Type select list in the Catalog task.

Testing Percentage

Type the percentage of the welds on this pipe run that are to be tested. This option is available only if you are viewing pipe run properties.

Insulation and Tracing

Insulation Specification

Displays the insulation specification for the object. You define which insulation specifications are available for which systems in the System and Specifications task. You define insulation specifications in the reference data.

Insulation Purpose

Displays the purpose of the insulation. You can define insulation purposes in the Catalog task.

Insulation Material

Displays the material of the insulation. You can define insulation material in the Catalog task.

Insulation Thickness

Displays the thickness of the insulation.

Insulation Temperature

Type the temperature. Include the temperature unit of measure (K for Kelvin, F for Fahrenheit, or C for Celsius, for example) when specifying this value.

Heat Tracing Requirement

Select whether or not the object is heat-traced. If you want to add, edit, or remove values that are available for selection, edit the Heat Tracing Medium select list in the Catalog task.

Heat Tracing Type

Select the type of heat-tracing. If you want to add, edit, or remove values that are available for selection, edit the Heat Tracing Medium select list in the Catalog task.

Heat Tracing Medium

Select the heat-tracing medium to apply to the object. If you want to add, edit, or remove values that are available for selection, edit the Heat Tracing Medium select list in the Catalog task.

Heat Tracing Medium Temperature

Specify the temperature of the heat-tracing medium. Include the temperature unit of measure (K for Kelvin, F for Fahrenheit, or C for Celsius, for example) when specifying this value.

Temperature and Pressure

If service limits have been defined, you must define one set of pressure/temperature values (Design Maximum Temperature and Design Maximum Pressure, for example) before you can place the object. The software does not prevent you from defining testing temperatures and pressures that exceed the defined service limits.

Design Maximum Temperature

Specify the maximum design temperature for the object. Include the temperature unit of measure (K for Kelvin, F for Fahrenheit, or C for Celsius, for example) when specifying this value.

Design Minimum Temperature

Specify the minimum design temperature for the object. Include the temperature unit of measure (K for Kelvin, F for Fahrenheit, or C for Celsius, for example) when specifying this value.

Design Maximum Pressure

Specify the maximum design pressure for the object. Include the pressure unit of measure (psi for pounds per square inch, for example) when specifying this value.

Operating Maximum Temperature

Specify the maximum operating temperature for the object. Include the temperature unit of measure (K for Kelvin, F for Fahrenheit, or C for Celsius, for example) when specifying this value.

Operating Minimum Temperature

Specify the minimum operating temperature for the object. Include the temperature unit of measure (K for Kelvin, F for Fahrenheit, or C for Celsius, for example) when specifying this value.

Operating Maximum Pressure

Specify the maximum operating pressure for the object. Include the pressure unit of measure (psi for pounds per square inch, for example) when specifying this value.

Testing Maximum Temperature

Specify the maximum testing temperature for the object. Include the temperature unit of measure (K for Kelvin, F for Fahrenheit, or C for Celsius, for example) when specifying this value.

Testing Minimum Temperature

Specify the minimum testing temperature for the object. Include the temperature unit of measure (K for Kelvin, F for Fahrenheit, or C for Celsius, for example) when specifying this value.

Testing Maximum Pressure

Specify the maximum testing pressure for the object. Include the pressure unit of measure (psi for pounds per square inch, for example) when specifying this value.

Design Minimum Pressure

Specify the minimum design pressure for the object. Include the pressure unit of measure (psi for pounds per square inch, for example) when specifying this value.

Operating Minimum Pressure

Specify the minimum operating pressure for the object. Include the pressure unit of measure (psi for pounds per square inch, for example) when specifying this value.

Testing Minimum Pressure

Specify the minimum testing pressure for the object. Include the pressure unit of measure (psi for pounds per square inch, for example) when specifying this value.

Adding Custom Default Properties

You can add your own custom default properties to this tab by editing the ..\CatalogData\Bulkload\SampleDataFiles\SystemUserDefinedDefaultProperties.xls workbook, and then bulkloading the edited workbook into your Catalog. For more information about bulkloading workbooks, refer to the Smart 3D Reference Data Guide, available from Help > Printable Guide. Only properties for piping, electrical, and conduit systems can be added to this tab.

The interfaces for the default property values are limited to the following: IJUASASSPipingDefaults, IJUASASSElectircalDefaults, and IJUASASSConduitDefaults. You must use these interfaces for the properties that you want to add to this tab.

The categories for the default property values are limited also. For Piping systems, the categories are: Standard, Responsibility, Surface Treatment and Coating, Testing, Insulation and Tracing, and Temperature.

For Electrical systems, the categories are: Standard, Responsibility, Surface Treatment and Coating, and Cable Fill.

For Conduit Systems, the categories are: Standard, Responsibility, Surface Treatment and Coating, and Cable Fill.

See Also

Define default property values