Plotted Material and Cut Pipe List Heading Texts - PDS - Reference

Plant Design System (PDS) ISOGEN

PPMProductFamily
3D Design and Visualization
PPMProduct
PDS
PPMCategory
Reference
Version_S3D
12.x(2018)

-274

(Normally blank)

If set, is used as a separator between the pipeline reference and the spool identifier in the spool isometric drawing identifier.

-300

FABRICATION MATERIALS

Is the category heading under which components required for SHOP Fabrication are listed.

-301

PT

Is the part number heading used in conjunction with AText -302 to form a composite message.

-302

NO

Used in conjunction with AText -301 to form a composite message.

-303

COMPONENT DESCRIPTION

Is the heading in the material listing under which components are described according to their catalog component description.

-304

N.S.

Is the heading under which the nominal size of each item is listed. Is used in conjunction with AText -330 or AText -331 to form a composite message.

-305

ITEM CODE

Is the heading under which component identification codes are listed.

-306

QTY

Is the heading under which the required quantities are listed.

-307

PIPE

Is the group sub-heading under which pipe is listed.

-308

FITTINGS

Is the group sub-heading under which pipe fittings are listed, such as elbows tees, and so.

-309

FLANGES

Is the group sub-heading under which all flanges are listed.

-310

ERECTION MATERIALS

Is the category heading under which components required for SITE Erection--or Construction--are listed.

-311

GASKETS

Is the group sub-heading under which all gaskets are listed

-312

BOLTS

Is the group sub-heading under which all bolts are listed.

-313

VALVES / IN-LINE ITEMS

Is the group sub-heading under which all valves and in-line Items are listed.

-314

INSTRUMENTS

Is the group sub-heading under which all instruments are listed.

-315

SUPPORTS

Is the group sub-heading under which all supports are listed.

-316

PIPE SPOOLS

Is the sub-heading under which all spool numbers are listed.

-319

CUT PIPE LENGTH

Is the heading under which all the cut pipe lengths are listed.

-320

PIECE

Is the sub-heading to AText -319 under which the cut pipe piece numbers are listed. This AText is used in conjunction with AText -321 to form a composite heading.

-321

NO

Used in conjunction with AText -320 to form a composite heading.

-322

CUT

Is the sub-heading to AText -319 under which the actual cut pipe lengths are listed. This AText is used in conjunction with AText -323 to form a composite heading.

-323

LENGTH

Used in conjunction with AText -322 to form a composite heading.

-324

REMARKS

Is the sub-heading to AText -319 under which one of the ATexts -326, -327, -328, or -500, if applicable, is listed.

-325

(Normally blank)

Used for spool number separator on the material list.

-326

PLD BEND

Used for a pulled bend remark, which is listed under AText -324 if a cut pipe length contains a pulled bend.

-327

LOOSE FLG

Is a remark which will be listed under AText -324 if a cut pipe length has a loose flange requirement.

-328

FF WELD

Is the field fit weld remark which is listed under AText -324 if a cut pipe length contains a field fit weld.

-329

M

Used to denote lengths of pipe are in metres. Also used to indicate unit type metres in centreline length summary.

-330

INS

Used to denote nominal sizes are in inches. It is used in conjunction with AText -304 and AText -317.

-331

MM

Denotes the nominal sizes are in millimetres. Also used to indicate unit type Millimetres in centreline length summary. It is used in conjunction with AText -304 and AText -317.

-334

S

Is used only on fixed length piping. The contents of this AText are appended to the item code to form a composite code when one or more ends of the fixed length spool has a special flange.

-335

WITH SPECIAL RATING FLANGE(S) (SEE ISO)

Is used only on fixed length piping. The contents of the AText are appended to the item description to form a composite message. Is used whenever AText -334 is used.

-339

MISCELLANEOUS COMPONENTS

Is the group sub-heading under which all non-categorized components are listed.

-340

INDUCTION BEND ID -

Used to identify pipe required in the fabrication of induction bends. The induction bend tag is appended to the AText to form a complete text string.

-341

EQUIPMENT TRIM MATERIALS

Is the sub-heading under which all equipment trim materials are listed.

-342

NOZZLE REF -

Is the sub-heading under which all materials associated with an individual nozzle are listed. The content of the related NOZZLE-REFERENCE is appended to the AText to form a complete text string. Used on equipment trim drawings only.

-343

CONTINUED

Used with AText -342 to identify situations where the listing of components for a nozzle is being continued from a previous drawing. Used on equipment trim drawings only.

-344

END CONNECTORS

Is the group sub-heading under which all materials for end connectors for hygienic type piping are listed (liners, nuts, clamps, and so on.).

-345

AND

Used with AText -342 to form a sub-heading under which all components associated with interconnected nozzles are output on the material list for an equipment trim drawing. The resultant heading is of the form NOZZLE REF - N22 AND N23.

-347

(Normally blank)

This has no default AText but is available as an alternative to the AText used when generating a material list overflow message at the bottom of the master drawing material list (an AText -209 and AText -255 combination). Any AText set by the user has a software-generated cross-reference drawing number appended to it to form a composite message.

-348

(Normally blank)

This has no default AText but is available as an alternative to the AText used when generating a material list overflow message at the top of overflow material list drawings ( AText -276 and AText -255 combination). Any AText set by the user has a software-generated cross reference drawing number appended.

-351

FABRICATED (PULLED) BEND

Used to identify fabricated bends when listed as separate items on the material list.

-352

WEIGHT

Column heading for weight.

-353

KGS

Units indicator for kilogram weights. Used as part of Weight column heading and in pipeline weight summary area at bottom of material list.

-354

LBS

Units indicator for pound weights. Used as part of Weight column heading and in pipeline weight summary area at bottom of material list

-355

TOTAL WEIGHT-THIS DRG

Identification text for total pipeline weight in Weight column and also in weight summary area at bottom of material list.

-356

U

Special ATEXT used only to identify special type pulled bends. Is used both on the material list and on the isometric area as a prefix to the part number.

-357

B

Special ATEXT used only to identify special type erection welds. Is used both on the material list and on the isometric area as a prefix to the part number.

-358

W

Special ATEXT only to identify special type fabrication welds. Is used both on the material list and on the isometric area as a prefix to the part number.

-359

(Normally blank)

Used for bolt units sub-heading. ISOGEN outputs in DIA x LENGTH sequence.

-362

END$ONE

Column heading on cut pipe list. (Also appears in the isometric drawing area section when it is necessary to identify a specific end of a cut piece).

-363

END$TWO

Column heading on cut pipe list.

-364

ITEM$CODE

Last column heading on cut pipe list when item code heading is required. (See Also AText -365).

-365

(Normally blank)

Alternative last column heading on cut pipe list. (See Also AText -364). If part number is required on the cut list instead of item code, then AText -364 should be set to blank, and AText -365 set to the required alternative heading, such as part no.

-366

SQ.CUT

Used for square cut in End Condition columns on cut pipe list.

-367

BEVEL

Used for bevel in End Condition columns on cut pipe list.

-368

SCREWED

Used for screwed in End Condition columns on cut pipe list.

-369

SHAPED

Used for shaped in End Condition columns on cut pipe list.

-370

MITRED

Used for mitered in End Condition columns on cut pipe list.

-371

OFFSHORE MATERIALS

Is the category heading under which components required for OFFSHORE erection are listed.

-372

REMARKS

Remarks region heading at bottom of material list where remarks text is collectively listed.

-373

REM

Remarks column heading in material list. Remark reference numbers are listed in this column.

-374

ANGLE

Used on special type pulled bends where angle information is appended to the item Description field on the material list.

-375

WELDS

Is the group sub-heading under which all welds are listed.

-376

FAB

Used to identify Fabrication material when category is used as a data item on a Style 2 or 3 material list.

-377

EREC

Used to identify Erection material when category is used as a data item on a Style 2 or 3 material list.

-378

OFF

Used to identify Offshore material when category is used as a data item on a Style 2 or 3 material list.

-379

TOTAL FABRICATION WEIGHT

Identification text for total fabrication weight in Weight column and also in weight summary area at bottom of material list.

-380

TOTAL ERECTION WEIGHT

Identification text for total erection weight in Weight column and also in weight summary area at bottom of material list.

-381

TOTAL OFFSHORE WEIGHT

Identification text for total offshore weight in Weight column and also in weight summary area at bottom of material list.

-382

TOTAL WEIGHT UNLISTED ITEMS

Identification text for the total weight of unlisted items in the Weight column and also in the weight summary area at the bottom of the material list.

-383

*

Missing weight indicator. The * is a special marker that is used on both weight and CoG outputs to indicate that component(s) with zero weight were encountered.

-384

TANGENT+

Used in the REMARKS column of the cut list to indicate where extra material has been added to a cut piece length in order to provide a minimum tangent length for either a start or finish bend leg.

-385

CUT/WELD

Used in the cut piece remarks section against cut pieces that have additional material added between adjacent bends.

-426

GROOVED

Used to indicate grooved end preparation for Victaulic pipe connections on the cut pipe list/report.

-427

FLARED

Used to indicate a flared end preparation on the cut pipe list/report.

-428

SCREWED

Used to indicate a female screwed end preparation on the cut pipe list/report.

-431

SOCKET

Used to indicate a female socket weld/compression/glued/push fit end preparation on the cut pipe list/report.

-472

No.?

Used to output a location point ID number on the drawing frame. Is only output when multiple location points are included on a single isometric.

-473

OF

Used as part of a location point position on the drawing frame.

-474

ABOVE

Used as part of a location point position on the drawing frame.

-500

SHOP TEST

Used on the cut list to identify cut pieces that need to have an additional shop test allowance. (That is welds with the SKEY WSST or WFST).

-503

SPOOL ID

Used as either a header or column identifier on the following printed output whenever spool identifiers are listed.

i) Printed material list (Style 1 or 2).

ii) Printed material control file.

iii) Printed weld summary.

-514

REINFPAD

Used as the item code for a reinforcement pad whenever automatic item code generation is requested.

-515

REINFORCEMENT PAD FOR @

Used as the first part of a description for a reinforcement pad whenever automatic description generation is requested. The second part of the pad description is the description of the main pipeline tube to which the pad is welded.

-537

(Normally blank)

If set, is used as an alternative units indication on any length output on any style of material list. (Overrules any length units setting in Option Switch. 24 ).

-538

(Normally blank)

If set, is used to offer an alternative form of bolt diameter/length output on any style of material list.

-540

(Normally blank)

If set, is used as an optional column heading for bolt diameter where the bolt units are different to the normal pipeline units.

-554

(Normally blank)

If set, outputs text to supplement scalar quantities output to the material list on the drawing and material control file.

-555

SPOOL -

If set, identifies materials belonging to spools on the material list.