These properties specify and customize the main steel member in the support.
Attribute Name |
Description |
Implementation Details |
---|---|---|
IJUAhsLeg1::Leg1Part |
Specifies the steel part number for the first support leg. To select the part number using Leg1Rule, do not type any value for this property. |
|
IJUAhsLeg1Rl::Leg1Rule |
Defines an HgrSupportRule that returns a rich hanger beam part number. To select the part number using Leg1Part, do not type any value for this property. |
|
IJUAhsLeg1Ang::Leg1OrientationAngle |
Specifies the angle of rotation about the axis of the leg for the first member of the support. |
hsSteelOrientalAngle: |
IJUAhsLeg1BeginOH::Leg1BeginOverhangValue |
Specifies a numerical value for the distance that the first leg should overhang past the main member. To select the overhang value using Leg1BeginOverhangRule, do not type any value for this property. |
|
IJUAhsLeg1BeginOHRl::Leg1BeginOverhangRule |
Defines an HgrSupportRule that returns the distance that the first leg should overhang past the main member. The hanger rule should exist in the catalog; it can be a rule name or a ProgID. The rule must return the value in the DB Units (meters). To select the overhang value directly using Leg1BeginOverhangValue, do not type any value for this property. |
|
IJUAhsLeg1BeginOHSel::Leg1BeginOverhangSelection |
Uses the hsSelection codelist in the HS_S3DAssy_Codelist.xls workbook to select Leg1BeginOverhang by either input or rule. Allowed values are: |
By Rule - 1 - Leg1BeginOverhangRule is used By Input - 2 - Leg1BeginOverhangValue is used |
IJUAhsLeg1EndOHRl::Leg1EndOverhangRule |
Defines an HgrSupportRule that returns the distance that the first leg should overhang past the supporting object. The hanger rule must exist in the catalog; it can be a rule name or a ProgID. To select the value of the overhang directly using Leg1EndOverhangValue, do not type any value for this property. |
|
IJUAhsLeg1EndOHDef::Leg1EndOverhangDefinition |
Defines how the end overhang should be measured with respect to the supporting object. If you do not type any value, a default value of 1 is used. The following values are allowed: |
|
IJUAhsLeg1EndOHSel::Leg1EndOverhangSelection |
Uses the hsSelection Codelist in the HS_S3DAssy_Codelist.xls workbook to select Leg1EndOverhang by either input or rule. Allowed values are: |
By Rule - 1 - Leg1BeginOverhangRule is used By Input - 2 - Leg1BeginOverhangValue is used |
IJUAhsCapPlate1::CapPlate1Part |
Specifies the part number or the part class of the plate placed at the end of the main section and at the end connected to the first leg. This must be a SmartPart 2 Port Plate. To select the part using CapPlate1Rule, do not type any value for this property. |
|
IJUAhsCapPlate1Rl::CapPlate1Rule |
Defines an HgrSupportRule that returns a part number or the part class to use for the cap plate. The hanger rule must exist in the catalog; it can be a rule name or a ProgID. To specify the part directly using CapPlate1Part, do not type any value for this property. CapPlate1Rule can also be used to specify a custom part selection rule. If both CapPlate1Part and CapPlate1Rule are populated, then it is assumed that CapPlate1Rule is a part selection rule, which will then be used to override the default part selection rule defined in the catalog for the part class specified in CapPlate1Part. |
|
IJUAhsCapPlate1Ang::CapPlate1Angle |
Specifies the angle that CapPlate1 should be rotated about the Z-axis of the port to which the plate is attached (either BeginFace or EndFace). |
|
IJUAhsLeg2::Leg2Part |
Specifies the steel part number for the first support leg. To select the part number using Leg2Rule, do not type any value for this property. |
|
IJUAhsLeg2Rl::Leg2Rule |
Defines an HgrSupportRule that returns a rich hanger beam part number. To select the part number using Leg2Part, do not type any value for this property. |
|
IJUAhsLeg2Ang::Leg2OrientationAngle |
Specifies the angle of rotation about the axis of the leg for the first member of the support. |
hsSteelOrientalAngle: |
IJUAhsLeg2BeginOH::Leg2BeginOverhangValue |
Specifies a numerical value for the distance that the first leg should overhang past the main member. To select the overhang value using Leg2BeginOverhangRule, do not type any value for this property. |
|
IJUAhsLeg2BeginOHRl::Leg2BeginOverhangRule |
Defines an HgrSupportRule that returns the distance that the first leg should overhang past the main member. The hanger rule should exist in the catalog; it can be a rule name or a ProgID. The rule must return the value in the DB Units (meters). To select the overhang value directly using Leg2BeginOverhangValue, do not type any value for this property. |
|
IJUAhsLeg2BeginOHSel::Leg2BeginOverhangSelection |
Uses the hsSelection codelist in the HS_S3DAssy_Codelist.xls workbook to select Leg2BeginOverhang by either input or rule. Allowed values are: |
By Rule - 1 – Leg2BeginOverhangRule is used By Input - 2 – Leg2BeginOverhangValue is used |
IJUAhsLeg2EndOHRl::Leg2EndOverhangRule |
Defines an HgrSupportRule that returns the distance that the first leg should overhang past the supporting object. The hanger rule must exist in the catalog; it can be a rule name or a ProgID. To select the value of the overhang directly using Leg2EndOverhangValue, do not type any value for this property. |
|
IJUAhsLeg2EndOHDef::Leg2EndOverhangDefinition |
Defines how the end overhang should be measured with respect to the supporting object. If you do not type any value, a default value of 1 is used. The following values are allowed: |
|
IJUAhsLeg2EndOHSel::Leg2EndOverhangSelection |
Uses the hsSelection Codelist in the HS_S3DAssy_Codelist.xls workbook to select Leg2EndOverhang by either input or rule. Allowed values are: |
By Rule - 1 – Leg2BeginOverhangRule is used By Input - 2 - Leg1BeginOverhangValue is used |
IJUAhsCapPlate2::CapPlate2Part |
Specifies the part number or the part class of the plate placed at the end of the main section and at the end connected to the first leg. This must be a SmartPart 2 Port Plate. To select the part using CapPlate2Rule, do not type any value for this property. |
|
IJUAhsCapPlate2Rl::CapPlate2Rule |
Defines an HgrSupportRule that returns a part number or the part class to use for the cap plate. The hanger rule must exist in the catalog; it can be a rule name or a ProgID. To specify the part directly using CapPlate2Part, do not type any value for this property. CapPlate2Rule can also be used to specify a custom part selection rule. If both CapPlate2Part and CapPlate2Rule are populated, then it is assumed that CapPlate2Rule is a part selection rule, which will then be used to override the default part selection rule defined in the catalog for the part class specified in CapPlate2Part. |
|
IJUAhsCapPlate2Ang::CapPlate2Angle |
Specifies the angle that CapPlate2 should be rotated about the Z-axis of the port to which the plate is attached (either BeginFace or EndFace). |
|
IJUAhsMember1::Member1Part |
Specifies the steel part number to use for the main support section. The part number specified must be a rich hanger beam. To select the part number using Member1Rule, do not type any value for this property. |
|
IJUAhsMember1Rl::Member1Rule |
Defines an HgrSupportRule that returns a rich hanger beam part number. The hanger rule must exist in the catalog; it can be the name of a rule, or a rule ProgID. To select a part number directly using Member1Part, do not type any value for this property. |
Option 1 - Specify a part number or part class directly. Option 2 - Use HgrRule to get the part. The base support is a mandatory part. Specify either a Member1Part or Member1Rule. |
IJUAhsMember1Ang::Member1OrientationAngle |
Specifies the angle of rotation for the main member. The angle is about the member's axis. |
The following values are allowed: |
IJUAhsMember1EndOH::Member1EndOverhangValue |
Defines the distance that the main section should overhang past the second leg. To specify the overhang value using Member1EndOverhangRule, do not type any value for this property. |
|
IJUAhsMember1EndOHRl::Member1EndOverhangRule |
Defines an HgrSupportRule that returns the distance that the main section should overhang past the second leg. The hanger rule must exist in the catalog; it can be a rule name or a ProgID. To select the overhang value directly using Member1EndOverhangValue, do not type any value for this property. |
|
IJUAhsMember1EndOHDef::Member1EndOverhangDefinition |
Defines how the EndOverhang should be measured. This property is applicable to U, I and L Frame types. The following values are allowed: |
|
IJUAhsMember1EndOHSel::Member1EndOverhangSelection |
Uses the hsSelection codelist in the HS_S3DAssy_Codelist.xls workbook to select the Member1EndOverhang by either input or rule. The following values are allowed: |
By Rule - 1 – Member1EndOverhangRule is used By Input - 2 – Member1EndOverhangValue is used |
IJUAhsCapPlate3::CapPlate3Part |
Specifies the part number or the part class of the plate placed at the end of the main section and at the end connected to the first leg. This must be a SmartPart 2 Port Plate. To select the part using CapPlate3Rule, do not type any value for this property. |
|
IJUAhsCapPlate3Rl::CapPlate3Rule |
Defines an HgrSupportRule that returns a part number or the part class to use for the cap plate. The hanger rule must exist in the catalog; it can be a rule name or a ProgID. To specify the part directly using CapPlate3Part, do not type any value for this property. CapPlate3Rule can also be used to specify a custom part selection rule. If both CapPlate3Part and CapPlate3Rule are populated, then it is assumed that CapPlate3Rule is a part selection rule, which will then be used to override the default part selection rule defined in the catalog for the part class specified in CapPlate3Part. |
|
IJUAhsCapPlate3Ang::CapPlate3Angle |
Specifies the angle that CapPlate3 should be rotated about the Z-axis of the port to which the plate is attached (either BeginFace or EndFace). |
|
IJUAhsCapPlate4::CapPlate4Part |
Specifies the part number or the part class of the plate placed at the end of the main section and at the end connected to the first leg. This must be a SmartPart 2 Port Plate. To select the part using CapPlate4Rule, do not type any value for this property. |
|
IJUAhsCapPlate4Rl::CapPlate4Rule |
Defines an HgrSupportRule that returns a part number or the part class to use for the cap plate. The hanger rule must exist in the catalog; it can be a rule name or a ProgID. To specify the part directly using CapPlate4Part, do not type any value for this property. CapPlate4Rule can also be used to specify a custom part selection rule. If both CapPlate4Part and CapPlate4Rule are populated, then it is assumed that CapPlate4Rule is a part selection rule, which will then be used to override the default part selection rule defined in the catalog for the part class specified in CapPlate4Part. |
|
IJUAhsCapPlate4Ang::CapPlate4Angle |
Specifies the angle that CapPlate4 should be rotated about the Z-axis of the port to which the plate is attached (either BeginFace or EndFace). |
|
IJUAhsCornerConn1Type::Connection1Type |
Specifies the type of connection to use when connecting Leg1 to Member1. Applicable to U, L, T, and Box Frame types only. Allowed values are from the hsSteelCornerConnection or hsSteelTeeConnection codelist in the HS_S3DAssy_Codelist.xls workbook. These values are: |
0 - Butted 1 - Lapped 2 - Nested 4 - Coped 5 - Mitered (Not applicable for T-Frame) |
IJUAhsCornerConn1Swap::Connection1Swap |
Specifies whether the connection between Leg1 and Member1 is swapped so that they are connected in the reversed order. This property accepts two values, 0 and 1. |
0 False - Member1 connects into the section of Leg1. 1 True - Leg1 connects into the cross section of Member1. |
IJUAhsCornerConn1Mirror::Connection1Mirror |
Specifies whether to mirror the connection between Leg1 and Member1 if the connection type has a valid mirrored configuration. For a lapped connection, the steel section laps to the opposite side. For a nested connection, the steel section nests into the opposite corner if one exists. This property accepts Boolean values 0 and 1 |
0 (False) 1 (True) |
IJUAhsCornerConn2Type::Connection2Type |
Specifies the type of connection to use when connecting Leg2 to Member1. Allowed values are from the hsSteelCornerConnection or hsSteelTeeConnection codelist in the HS_S3DAssy_Codelist.xls workbook. These values are: |
0 - Butted 1 - Lapped 2 - Nested 4 - Coped 5 - Mitered (Not applicable for T-Frame) |
IJUAhsCornerConn2Swap::Connection2Swap |
Specifies whether the connection between Leg1 and Member1 is swapped so that they are connected in the reversed order. Applicable to U, L, and Box Frame types only. This property accepts two values, 0 and 1. |
0 False - Member1 connects into the section of Leg1. 1 True - Leg1 connects into the cross section of Member1. |
IJUAhsCornerConn2Mirror::Connection2Mirror |
Specifies whether to mirror the connection between Leg2 and Member1 if the connection type has a valid mirrored configuration. For a lapped connection, the steel section laps to the opposite side. For a nested connection, the steel section nests into the opposite corner if one exists. This property accepts Boolean values 0 and 1 and is applicable to U, L, T, and Box Frame types only. |
0 (False) 1 (True) |
IJUAhsBasePlate1::BasePlate1Part |
Specifies the part number or part class of the first base plate. This must be a SmartPart 2 Port Plate. To select the part using BasePlate1Rule, do not type any value for this property. |
|
IJUAhsBasePlate1Rl::BasePlate1Rule |
Defines an HgrSupportRule that returns a part number or part class to use for the base plate. The hanger rule must exist in the catalog; it can be a rule name or a ProgID. To select the part directly using BasePlate1Part, do not type any value for this property. |
|
IJUAhsBasePlate1Ang::BasePlate1Angle |
Specifies the angle that BasePlate1 should be rotated about the Z-axis of the port to which the plate is attached (either BeginFace or EndFace). |
|
IJUAhsFrGrout::GroutPart |
Specifies the part number or the part class of the grout part. For example Plate part number. To select the part using GroutRule, do not type any value for this property. |
|
IJUAhsFrGroutRl::GroutRule |
Defines an HgrSupportRule. The hanger rule must exist in the catalog; it can be a rule name or a ProgID. To specify the grout part directly using GroutPart, do not type any value for this property. |
|
IJUAhsFrGroutTh::GroutThickness |
Specifies the thickness of the GroutPart. |
|
IJUAhsBolt1::Bolt1Part |
Specifies the part number or the part class of the Bolt part. For example Plate part number. To select the part using Bolt1Rule, do not type any value for this property. |
|
IJUAhsBolt1Rl::Bolt1Rule |
Defines an HgrSupportRule. The hanger rule must exist in the catalog; it can be a rule name or a ProgID. |
|
IJUAhsBolt1Qty::Bolt1Quantity |
Specifies the quantity of the Bolt1Part. |
|
IJUAhsBolt1Offset1::Bolt1Offset1 |
Specifies the offset1 value of the Bolt1Part. |
|
IJUAhsBolt1Offset2::Bolt1Offset2 |
Specifies the offset2 value of the Bolt2Part. |
|
IJUAhsBasePlate2::BasePlate2Part |
Specifies the part number or part class of the first base plate. This must be a SmartPart 2 Port Plate. To select the part using BasePlate2Rule, do not type any value for this property. |
|
IJUAhsBasePlate2Rl::BasePlate2Rule |
Defines an HgrSupportRule that returns a part number or part class to use for the base plate. The hanger rule must exist in the catalog; it can be a rule name or a ProgID. To select the part directly using BasePlate2Part, do not type any value for this property. |
|
IJUAhsBasePlate2Ang::BasePlate2Angle |
Specifies the angle that BasePlate2 should be rotated about the Z-axis of the port to which the plate is attached (either BeginFace or EndFace). |
|
IJUAhsFrGrout2::Grout2Part |
Specifies the part number or the part class of the grout part. For example Plate part number. To select the part using GroutRule, do not type any value for this property. |
|
IJUAhsFrGrout2Rl::Grout2Rule |
Defines an HgrSupportRule. The hanger rule must exist in the catalog; it can be a rule name or a ProgID. To specify the grout part directly using GroutPart2, do not type any value for this property. |
|
IJUAhsFrGrout2Th::Grout2Thickness |
Specifies the thickness of the GroutPart2. |
|
IJUAhsBolt2::Bolt2Part |
Specifies the part number or the part class of the Bolt part. For example Plate part number. To select the part using Bolt2Rule, do not type any value for this property. |
|
IJUAhsBolt2Rl::Bolt2Rule |
Defines an HgrSupportRule. The hanger rule must exist in the catalog; it can be a rule name or a ProgID. |
|
IJUAhsBolt2Qty::Bolt2Quantity |
Specifies the quantity of the Bolt2Part. |
|
IJUAhsBolt1Offset2::Bolt2Offset1 |
Specifies the offset1 value of the Bolt1Part. |
|
IJUAhsBolt2Offset2::Bolt2Offset2 |
Specifies the offset2 value of the Bolt2Part. |