Error Messages - PDS - Help

E1

Error opening error message file - pdsstr.err

An error occurred while trying to open the error message file. Check to make sure that the file pdsstr.err is not opened by another user in the default directory.

E3

Error opening input data file - PDSSTR.DAT

An error occurred while attempting to open the input file to the stress analysis interface. Check to make sure that the file PDSSTR.DAT exists in the default directory.

E4

Word 11 in the INTERGRAPH OPTIONS BLOCK is undefined

Word 11 in the options block must be set to 1.

E5

No model files found in input data file - PDSSTR.DAT

An error occurred generating PDSSTR.DAT or the user entered a blank first line in the input data file and no model file names were found. Check to make sure there are valid model file names in PDSSTR.DAT in the default directory.

E6

No line names found in input data file - PDSSTR.DAT

An error occurred generating PDSSTR.DAT or the user entered two blank lines between the last model file name and the first line name. Check to make sure there is only one blank line between the last model file name and the first line name in PDSSTR.DAT in the default directory.

E7

Word 12 in the INTERGRAPH OPTIONS BLOCK is undefined

Word 12 in the options block must be set to 1.

E8

Error opening stress options file

E9

Fatal SEQUENCER error

An error occurred while organizing the design file components. Check the model design file to verify that the pipeline being extracted is free of modeling errors. If the pipeline is correct, contact Intergraph.

E10

Error reading input data file - PDSSTR.DAT

An error occurred reading information from the input data file. Check the record format of the input data file PDSSTR.DAT in the default directory.

E11

Logical name STRESSOPTION is undefined or file does not exist

E15

Number of connect points exceeded internal limit of 5000 connect points

The maximum number of connect points per extraction is 5,000. Break the line into two separate line names and re-extract the line as two separate isometrics.

E16

Error reading FORM type from options file

An error occurred reading in the FORM type from a record in the ELEMENT PROPERTY / CONNECTIVITY TABLE section of the options file. Valid values for form type are 0-6. For more information on property and connectivity record refer to the Options File section.

E17

Error reading database occurrence

An error occurred in trying to read a record from the database on a design file linkage. This error indicates potentially serious problems in the model. It is strongly recommended that the model be analyzed to determine the extent of the problem and to correct the situation.

E18

Error retrieving DDL pair

This message means that an error occurred trying to read an attribute from the database. Check the database DDL to make sure the DDL pair in question consists of a valid entity and attribute number.

E19

Error retrieving DDL table

An undefined entity number has been read in from either the LOADING DATA (LOAD) TABLE, the SERVICE LOADING (LSET) TABLE or the ELEMENT PROPERTY / CONNECTIVITY TABLE in the options file. Check to make sure only valid entity numbers are used in the DDL pairs section of the above tables.

E20

Error writing CODE record

An error occurred while trying to write a CODE record to the STRESS ANALYSIS neutral file.

E21

Error converting Segment occurrence number from decimal to hex

An error occurred while trying to convert a Segment occurrence number from decimal format into a hexadecimal format. Contact Intergraph.

E22

Error writing header information into neutral file

An error occurred while trying to write the header records to the beginning of the stress analysis neutral file.

E23

Error writing DRAW record

An error occurred while trying to write a DRAW record to the stress analysis neutral file.

E24

Error converting nominal piping diameter

This message means there was an error trying to convert the nominal piping diameter from the database format to an ASCII format. Contact Intergraph.

E25

Error loading record from options file

E26

Invalid table for Insulation Weight

An error occurred trying to retrieve insulation weight for a table which does not have an insulation weight attribute. Verify that the DDL pair "0,-3" or "0,-4" is not any of the pipe support/hanger records in the ELEMENT PROPERTY / CONNECTIVITY TABLE section of the options file.

E27

End node number is too small for current line

An error occurred trying to assign an end node number to the current line being extracted. This can be fixed by increasing the end node number (word 3) of the INTERGRAPH OPTIONS BLOCK section of the options file.

E28

Internal table limits exceeded for PDS to STRESS map

The internal table size for the PDS to STRESS map has reached its limits and the remainder of the map can not be stored. Reduce the number of records in the PDS to STRESS map. Contact Intergraph for information about increasing the maximum table size.

E29

Error initializing spec table access information

An error occurred while trying to open and initialize the piping job specification tables. Check the project files to make sure they exist and you have read access to them.

E30

Error reading record from options file

An error occurred while trying to read a record from the options file. Check the bad record to make sure it is in the proper format.

E31

Error opening neutral file

An error occurred while trying to open the stress analysis output neutral file.

E33

No component was found that matches the database search criteria

An error occurred while trying to use the pipeline name keyin value. Either the value is missing, or word 12 is set incorrectly.

E34

Error writing LNOD record

An error occurred trying to write a LNOD record to the stress analysis neutral file.

E35

Error searching for PDS item name in PDS to stress analysis symbol map

An error occurred searching for PDS item name in the PDS to stress analysis symbol map. Check to make sure hte PDS item name is in the PDS to STRESS table.

E36

Undefined generic name in PDS to STRESS map

An error occurred in reading the generic name from the PDS to stress analysis symbol map. Check to make sure that the generic name is defined in the table.

E37

Error locating PROPERTY/CONNECTIVITY records for generic name

An error occurred searching for the PROPERTY / CONNECTIVITY record(s) from the ELEMENT PROPERTY / CONNECTIVITY TABLE section of the options file. Check to make sure all the necessary form records are in this table.

E38

Error reading standard note library

An error occurred while reading the standard note library. Check the standard note library to make sure the standard note exists.

E39

Error writing LSET record

An error occurred while trying to write a LSET record to the neutral file.

E40

Error writing NODE record

An error occurred while trying to write a NODE record to the neutral file.

E41

Error writing CONNECTIVITY record

An error occurred while trying to write a CONNECTIVITY record to the neutral file.

E42

Error writing PROPERTY record

An error occurred while to to write a PROPERTY record to the neutral file.

E43

Error accessing or opening PDS to STRESS map

An error occurred while trying to open the PDS to stress analysis symbol map. Check to make sure the file exists and that you have read access to it.

E44

Error reading PDS to STRESS map

An error occurred while trying to read a record from the PDS to stress analysis symbol map. Check to make sure the table is in the correct format.

E45

Error - line is composed of multiple disconnect section - number of sections: 2

An error occurred because your pipeline has a gap, or two separate pipelines have the same pipeline name or stress ID number.

E46

Line does not contain a valid starting point

An error occurred because a pipe support is at the end of the pipeline.

E49

Error writing LOAD record

An error occurred while trying to write LOAD record to the neutral file.

E50

Error searching for segment occurrence number

An error occurred while searching for the segment occurrence number from the current component. Check the model to make sure that components are owned by the correct segments.

E51

Error accessing wall thickness table

An error occurred while accessing information from the wall thickness table. Check the commodity library to make sure the wall thickness table exists.