-274 |
(Normally blank) |
If set, is used as a separator between the pipeline reference and the spool identifier in the spool isometric drawing identifier. |
-300 |
FABRICATION MATERIALS |
Is the category heading under which components required for SHOP Fabrication are listed. |
-301 |
PT |
Is the part number heading used in conjunction with AText -302 to form a composite message. |
-302 |
NO |
Used in conjunction with AText -301 to form a composite message. |
-303 |
COMPONENT DESCRIPTION |
Is the heading in the material listing under which components are described according to their catalog component description. |
-304 |
N.S. |
Is the heading under which the nominal size of each item is listed. Is used in conjunction with AText -330 or AText -331 to form a composite message. |
-305 |
ITEM CODE |
Is the heading under which component identification codes are listed. |
-306 |
QTY |
Is the heading under which the required quantities are listed. |
-307 |
PIPE |
Is the group sub-heading under which pipe is listed. |
-308 |
FITTINGS |
Is the group sub-heading under which pipe fittings are listed, such as elbows tees, and so. |
-309 |
FLANGES |
Is the group sub-heading under which all flanges are listed. |
-310 |
ERECTION MATERIALS |
Is the category heading under which components required for SITE Erection--or Construction--are listed. |
-311 |
GASKETS |
Is the group sub-heading under which all gaskets are listed |
-312 |
BOLTS |
Is the group sub-heading under which all bolts are listed. |
-313 |
VALVES / IN-LINE ITEMS |
Is the group sub-heading under which all valves and in-line Items are listed. |
-314 |
INSTRUMENTS |
Is the group sub-heading under which all instruments are listed. |
-315 |
SUPPORTS |
Is the group sub-heading under which all supports are listed. |
-316 |
PIPE SPOOLS |
Is the sub-heading under which all spool numbers are listed. |
-319 |
CUT PIPE LENGTH |
Is the heading under which all the cut pipe lengths are listed. |
-320 |
PIECE |
Is the sub-heading to AText -319 under which the cut pipe piece numbers are listed. This AText is used in conjunction with AText -321 to form a composite heading. |
-321 |
NO |
Used in conjunction with AText -320 to form a composite heading. |
-322 |
CUT |
Is the sub-heading to AText -319 under which the actual cut pipe lengths are listed. This AText is used in conjunction with AText -323 to form a composite heading. |
-323 |
LENGTH |
Used in conjunction with AText -322 to form a composite heading. |
-324 |
REMARKS |
Is the sub-heading to AText -319 under which one of the ATexts -326, -327, -328, or -500, if applicable, is listed. |
-325 |
(Normally blank) |
Used for spool number separator on the material list. |
-326 |
PLD BEND |
Used for a pulled bend remark, which is listed under AText -324 if a cut pipe length contains a pulled bend. |
-327 |
LOOSE FLG |
Is a remark which will be listed under AText -324 if a cut pipe length has a loose flange requirement. |
-328 |
FF WELD |
Is the field fit weld remark which is listed under AText -324 if a cut pipe length contains a field fit weld. |
-329 |
M |
Used to denote lengths of pipe are in metres. Also used to indicate unit type metres in centreline length summary. |
-330 |
INS |
Used to denote nominal sizes are in inches. It is used in conjunction with AText -304 and AText -317. |
-331 |
MM |
Denotes the nominal sizes are in millimetres. Also used to indicate unit type Millimetres in centreline length summary. It is used in conjunction with AText -304 and AText -317. |
-334 |
S |
Is used only on fixed length piping. The contents of this AText are appended to the item code to form a composite code when one or more ends of the fixed length spool has a special flange. |
-335 |
WITH SPECIAL RATING FLANGE(S) (SEE ISO) |
Is used only on fixed length piping. The contents of the AText are appended to the item description to form a composite message. Is used whenever AText -334 is used. |
-339 |
MISCELLANEOUS COMPONENTS |
Is the group sub-heading under which all non-categorized components are listed. |
-340 |
INDUCTION BEND ID - |
Used to identify pipe required in the fabrication of induction bends. The induction bend tag is appended to the AText to form a complete text string. |
-341 |
EQUIPMENT TRIM MATERIALS |
Is the sub-heading under which all equipment trim materials are listed. |
-342 |
NOZZLE REF - |
Is the sub-heading under which all materials associated with an individual nozzle are listed. The content of the related NOZZLE-REFERENCE is appended to the AText to form a complete text string. Used on equipment trim drawings only. |
-343 |
CONTINUED |
Used with AText -342 to identify situations where the listing of components for a nozzle is being continued from a previous drawing. Used on equipment trim drawings only. |
-344 |
END CONNECTORS |
Is the group sub-heading under which all materials for end connectors for hygienic type piping are listed (liners, nuts, clamps, and so on.). |
-345 |
AND |
Used with AText -342 to form a sub-heading under which all components associated with interconnected nozzles are output on the material list for an equipment trim drawing. The resultant heading is of the form NOZZLE REF - N22 AND N23. |
-347 |
(Normally blank) |
This has no default AText but is available as an alternative to the AText used when generating a material list overflow message at the bottom of the master drawing material list (an AText -209 and AText -255 combination). Any AText set by the user has a software-generated cross-reference drawing number appended to it to form a composite message. |
-348 |
(Normally blank) |
This has no default AText but is available as an alternative to the AText used when generating a material list overflow message at the top of overflow material list drawings ( AText -276 and AText -255 combination). Any AText set by the user has a software-generated cross reference drawing number appended. |
-351 |
FABRICATED (PULLED) BEND |
Used to identify fabricated bends when listed as separate items on the material list. |
-352 |
WEIGHT |
Column heading for weight. |
-353 |
KGS |
Units indicator for kilogram weights. Used as part of Weight column heading and in pipeline weight summary area at bottom of material list. |
-354 |
LBS |
Units indicator for pound weights. Used as part of Weight column heading and in pipeline weight summary area at bottom of material list |
-355 |
TOTAL WEIGHT-THIS DRG |
Identification text for total pipeline weight in Weight column and also in weight summary area at bottom of material list. |
-356 |
U |
Special ATEXT used only to identify special type pulled bends. Is used both on the material list and on the isometric area as a prefix to the part number. |
-357 |
B |
Special ATEXT used only to identify special type erection welds. Is used both on the material list and on the isometric area as a prefix to the part number. |
-358 |
W |
Special ATEXT only to identify special type fabrication welds. Is used both on the material list and on the isometric area as a prefix to the part number. |
-359 |
(Normally blank) |
Used for bolt units sub-heading. Isogen outputs in DIA x LENGTH sequence. |
-362 |
END$ONE |
Column heading on cut pipe list. (Also appears in the isometric drawing area section when it is necessary to identify a specific end of a cut piece). |
-363 |
END$TWO |
Column heading on cut pipe list. |
-364 |
ITEM$CODE |
Last column heading on cut pipe list when item code heading is required. (See Also AText -365). |
-365 |
(Normally blank) |
Alternative last column heading on cut pipe list. (See Also AText -364). If part number is required on the cut list instead of item code, then AText -364 should be set to blank, and AText -365 set to the required alternative heading, such as part no. |
-366 |
SQ.CUT |
Used for square cut in End Condition columns on cut pipe list. |
-367 |
BEVEL |
Used for bevel in End Condition columns on cut pipe list. |
-368 |
SCREWED |
Used for screwed in End Condition columns on cut pipe list. |
-369 |
SHAPED |
Used for shaped in End Condition columns on cut pipe list. |
-370 |
MITRED |
Used for mitered in End Condition columns on cut pipe list. |
-371 |
OFFSHORE MATERIALS |
Is the category heading under which components required for OFFSHORE erection are listed. |
-372 |
REMARKS |
Remarks region heading at bottom of material list where remarks text is collectively listed. |
-373 |
REM |
Remarks column heading in material list. Remark reference numbers are listed in this column. |
-374 |
ANGLE |
Used on special type pulled bends where angle information is appended to the item Description field on the material list. |
-375 |
WELDS |
Is the group sub-heading under which all welds are listed. |
-376 |
FAB |
Used to identify Fabrication material when category is used as a data item on a Style 2 or 3 material list. |
-377 |
EREC |
Used to identify Erection material when category is used as a data item on a Style 2 or 3 material list. |
-378 |
OFF |
Used to identify Offshore material when category is used as a data item on a Style 2 or 3 material list. |
-379 |
TOTAL FABRICATION WEIGHT |
Identification text for total fabrication weight in Weight column and also in weight summary area at bottom of material list. |
-380 |
TOTAL ERECTION WEIGHT |
Identification text for total erection weight in Weight column and also in weight summary area at bottom of material list. |
-381 |
TOTAL OFFSHORE WEIGHT |
Identification text for total offshore weight in Weight column and also in weight summary area at bottom of material list. |
-382 |
TOTAL WEIGHT UNLISTED ITEMS |
Identification text for the total weight of unlisted items in the Weight column and also in the weight summary area at the bottom of the material list. |
-383 |
* |
Missing weight indicator. The * is a special marker that is used on both weight and CoG outputs to indicate that component(s) with zero weight were encountered. |
-384 |
TANGENT+ |
Used in the REMARKS column of the cut list to indicate where extra material has been added to a cut piece length in order to provide a minimum tangent length for either a start or finish bend leg. |
-385 |
CUT/WELD |
Used in the cut piece remarks section against cut pieces that have additional material added between adjacent bends. |
-426 |
GROOVED |
Used to indicate grooved end preparation for Victaulic pipe connections on the cut pipe list/report. |
-427 |
FLARED |
Used to indicate a flared end preparation on the cut pipe list/report. |
-428 |
SCREWED |
Used to indicate a female screwed end preparation on the cut pipe list/report. |
-431 |
SOCKET |
Used to indicate a female socket weld/compression/glued/push fit end preparation on the cut pipe list/report. |
-472 |
No.? |
Used to output a location point ID number on the drawing frame. Is only output when multiple location points are included on a single isometric. |
-473 |
OF |
Used as part of a location point position on the drawing frame. |
-474 |
ABOVE |
Used as part of a location point position on the drawing frame. |
-500 |
SHOP TEST |
Used on the cut list to identify cut pieces that need to have an additional shop test allowance. (That is welds with the SKEY WSST or WFST). |
-503 |
SPOOL ID |
Used as either a header or column identifier on the following printed output whenever spool identifiers are listed. i) Printed material list (Style 1 or 2). ii) Printed material control file. iii) Printed weld summary. |
-514 |
REINFPAD |
Used as the item code for a reinforcement pad whenever automatic item code generation is requested. |
-515 |
REINFORCEMENT PAD FOR @ |
Used as the first part of a description for a reinforcement pad whenever automatic description generation is requested. The second part of the pad description is the description of the main pipeline tube to which the pad is welded. |
-537 |
(Normally blank) |
If set, is used as an alternative units indication on any length output on any style of material list. (Overrules any length units setting in Option Switch. 24 ). |
-538 |
(Normally blank) |
If set, is used to offer an alternative form of bolt diameter/length output on any style of material list. |
-540 |
(Normally blank) |
If set, is used as an optional column heading for bolt diameter where the bolt units are different to the normal pipeline units. |
-554 |
(Normally blank) |
If set, outputs text to supplement scalar quantities output to the material list on the drawing and material control file. |
-555 |
SPOOL - |
If set, identifies materials belonging to spools on the material list. |