Bottom Plate Properties - Intergraph Smart 3D - Reference Data

Intergraph Smart 3D Hangers and Supports SmartParts Configuration

Language
English
Product
Intergraph Smart 3D
Subproduct
3D Symbols
Search by Category
Reference Data
Smart 3D Version
12.1 (2019)

IJUAhsLength3::Length3

Specifies the length of the bottom plate. Length3 is an optional property and if you do not assign a value, the software does not display the top plate.

IJUAhsWidth3::Width3

Specifies the width of the bottom plate. Width3 is an optional property and if you do not assign a value, the software does not display the top plate.

IJUAhsThickness3::Thickness3

Specifies the thickness of the vertical plate. Thickness3 is an optional property and if you do not assign a value, the software does not display the top plate.

IJUAhsTLCorner3::TLCornerType3

Specifies the corner type of the bottom plate. Use codelist value 1 for this corner type. See the hsCornerShape sheet from the HS_S3DParts_Codelist.xls workbook for all the valid codes. CornerType3 is applicable for all the vertical plates if the plate quantity is greater than 1.

IJUAhsTLCorner3::TLCornerX3

Specifies the horizontal size of the rectangular notch. TLCornerX3 takes a positive value and must be less than the Width1 value.

IJUAhsTLCorner3::TLCornerY3

Specifies the vertical size of the rectangular notch. TLCornerY3 takes a positive value and must be less than the Height1-Thickness1 value.

IJUAhsTLCorner3::TLCornerRadius3

Specifies the radius of the angled notch shape. Use the TLCornerRadius3 value when the two outside points of the notch must be rounded using the corner radius value.

IJUAhsBLCorner3::BLCornerType3

Specifies the corner type of the bottom plate. Use codelist value 1 for this corner type. See the hsCornerShape sheet from the HS_S3DParts_Codelist.xls workbook for all the valid codes. CornerType3 is applicable for all the corner plates if the plate quantity is greater than 1.

IJUAhsBLCorner3::BLCornerX3

Specifies the horizontal size of the rectangular notch. BLCornerX3 takes a positive value and must be less than the Width1 value.

IJUAhsBLCorner3::BLCornerY3

Specifies the vertical size of the rectangular notch. BLCornerY3 takes a positive value and must be less than the Height1-Thickness1 value.

IJUAhsBLCorner3::BLCornerRadius3

Specifies the radius of the angled notch shape. Use the BLCornerRadius3 value when the two outside points of the notch must be rounded using the corner radius value.

IJUAhsTRCorner3::TRCornerType3

Specifies the corner type of the bottom plate. Use codelist value 1 for this corner type. See the hsCornerShape sheet from the HS_S3DParts_Codelist.xls workbook for all the valid codes. CornerType3 is applicable for all the corner plates if the plate quantity is greater than 1.

IJUAhsTRCorner3::TRCornerX3

Specifies the horizontal size of the rectangular notch. TRCornerX3 takes a positive value and must be less than the Width1 value.

IJUAhsTRCorner3::TRCornerY3

Specifies the vertical size of the rectangular notch. TRCornerY3 takes a positive value and must be less than the Height1-Thickness1 value.

IJUAhsTRCorner3::TRCornerRadius3

Specifies the radius of the angled notch shape. Use the TRCornerRadius3 value when the two outside points of the notch must be rounded using the corner radius value.

IJUAhsBRCorner3::BRCornerType3

Specifies the corner type of the bottom plate. Use codelist value 1 for this corner type. See the hsCornerShape sheet from the HS_S3DParts_Codelist.xls workbook for all the valid codes. CornerType3 is applicable for all the corner plates if the plate quantity is greater than 1.

IJUAhsBRCorner3::BRCornerX3

Specifies the horizontal size of the rectangular notch. BRCornerX3 takes a positive value and must be less than the Width1 value.

IJUAhsBRCorner3::BRCornerY3

Specifies the vertical size of the rectangular notch. BRCornerY3 takes a positive value and must be less than the Height1-Thickness1 value.

IJUAhsBRCorner3::BRCornerRadius3

Specifies the radius of the angled notch shape. Use the BRCornerRadius3 value when the two outside points of the notch must be rounded using the corner radius value.